[v888v]

Сообщение от sudima

Скажите какие параметры замерить и я замерю! Потом сброшу!

По давлению вот все имеющиеся пиды:

"(Out3) CVT Target LU diffirential pressure","TrgDifPres","2104","(SIGNED(E))/100","-1.28","1.27","Mpa","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
"(Out3) CVT Target line pressure","TrgLinPres","2104","F*6.38/255","0","6.38","Mpa","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
"(Out3) CVT Target secondary pressure","TrgSecPres","2104","G*6.38/255","0","6.38","Mpa","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
"(Out3) CVT Prim. Press","CVT Pr.Pres","2103","M/100","0","3","MPa","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
"(Out3) CVT Sec. Press","CVT Sec.Pres","2103","L/100","0","3","MPa","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"

Сам я пока не мониторил их.
Сравнить поездки придется по скорости, значит еще такие пиды:

"(Out3) CVT Accelerator Position","CVT Acc.Pos","2103","(G*100)/255","0","100","%","7E1","atsh7E1\natfcsh7E1\natfcsd30080a\natfcsm1\natcra7E9","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
"(OUT3) AWC FL Speed","AWC FL Speed","2107","(I*256+J)/100","0","250","km/h","7B6","atsh7B6\natfcsh7B6\natfcsd30080a\natfcsm1\natcra7B7","atsh7E0\natfcsh7E0\natfcsd30080a\natfcsm1\natcra7E8"
Скорость (OBD)

Внести "запись и выгрузка журналов" "Что записывать"
"Записывать показания выбранных ..." - галочка
"Синхронизация журналов" - снять галочку
"Интервал записи журналов" - выбрать "1 Seconds"
убрать лишнее, например:
"Автозапись данных GPS" - убрать